XS650 Direct

LED Charging system indicator Gauge. Shows Voltage of your alternator rising and
falling with RPM and gives a clear indication of your charging systems normal
operation and early warning of problems.
Gauge is Bright High Quality Chrome plated and clamps onto 7/8" Bars and can be
easily wired into any point in the system (before a switched load is best). Can be
mounted as shown or to handlebar by clamp (included).
Fits: All 650's 1970-84

AGM Battery - Fits: 1974-84 650's

CBTX14AHL-BS AGM Battery - XS# 61-2020
Absorbed Glass Mat(AGM) is the latest in motorcycle battery technology.
Sealed AGM batteries completely eliminate the hassels of conventional
battery maintenance. There is no liquid acid in the AGM battery. All of the
acid is absorbed into the compressed glass matting in the cells. They are
completely Non-Spillable, so they can be shipped by U.S. Mail or UPS with
no hazardous warnings or extra fees. They can be mounted in any position
for special applications. Our AGM batteries re-combine the oxygen and
hydrogen as the batteries charge and discharge to make them truly
maintenance free. No liquid ever needs to be added, No leaks, spills or vent
tubes. AGM batteries have higher cold cranking Amps and hold a charge
much longer. Replaces 12n14-3a / YB14LA2 original batteries

AGM Batteries Feature
Batteries are wet charged at the factory but contain no liquid acid.
Absorbed Glass Mat (AGM) technology eliminates the need to add electrollyte.
Built to withstand the demands of high-heat applications.
Lower internal resistance reduces charging time vs. conventional wet batteries.
Permaseal Design is Maintenance Free and Non-Spillable.
Resistant to vibration damage for reliable performance even under
rough off-road conditions.
Engineered to meet or exceed OEM specifications to ensure exact fit and power needs.
Slower self discharge rate means AGM batteries can sit for extended periods
of time without constant monitoring. A conventional wet battery discharges
15% a month where our AGM batteries discharge only 2-3% a month.

AGM Battery - Fits: XS2/TX650's 1972-1973
Replaces original 12n12a-4a-1
This high power version never existed before and was made in the sealed
maintenance free AGM type for Mikes XS. It will bring more power and durability
to your old early 650 electrical system.
170cca, 12volt AGM type (actual peak voltage 14.5 volts).
Dimensions - 5 5/16" Long x 3 3/16" wide x 6 5/16" high

Fully activated and ready to use!

Deluxe 12 Volt Battery Charger for AGM (Absorbed glass mat), Maintenance free,
VRLA, Gel and conventional flooded lead acid batteries. UL & CSA Approved.
Output is 1.25 Amps, 12 volt DC (maximum 14.5 Volts). 4 Stage Microprocessor
controlled charging with automatic shutoff at full charge. 120v AC Input.

1. Qualification - Ensures battery is safe to charge, and has minimum 3 Volts.
2. Bulk Charge - Raises battery to 80 percent of full voltage.
3. Absorption - Holds battery voltage at 80 percent and forces current to top battery
4. Float Mode - Maintains the fully charged battery at a proper working voltage.
Charger Features - 6 LED indicators to show charging status, reverse polarity
protection, overheat protection, overcharge protection and spark proofing.
Full instructions, quick disconnect alligator clip leads and fused eye terminal
leads included. (Not for outdoor use).

Battery Boot - Fits: 12N14 type Batteries as used on 1974-84 Yamaha 650's.

Battery Retainer Strap - As used on XS/TX 650's (1974-84)

Battery Retainer Strap - As used on XS2/TX650 (1972-73)

Battery top cover - Fits: 1978-84 "Specials".

Electrical Continuity Tester (use with power off) - Detects open circuit in fuses,
diodes, switches, sockets and wires (requires one AA battery - Not included).
Long 48" leads.

Electric Circuit Tester - Checks all motorcycle primary electrical and computer
circuits for power. Plastic handle lights up if circuit is good. Icepick type
probe and 48" cable with insulated alligator clips.

XS650 Fuse Boxes located on top of the battery are a part of the original wiring
harness and have Not been available separate. We now offer a copy of this
box as shown plus matching terminal block & terminals + the battery top cover
it attaches to. Cut the old fuse box from your main harness, attach the
connector block provided and plug in the new fuse box. Fits: All "Specials"
1978-84. Includes 25mm fuses.

Mini Fuse Holder
Shock proof construction.
Takes mini blade type fuses (5-20AMPS)

Fuse Holder with space for spare fuse( 30mm.) Correct terminals
(both have male ends) to replace fuse holder as used on all 1970-79
"Standard" models.

Fuse - Pk/5 - 25mm.(1 inch) Glass Fuse - 7 Amp.- Fits: 1978-84 "Specials".

Fuse - Pk/5 - 25mm.(1 inch) Glass Fuse - 10 Amp.- Fits: 1978-84 "Specials".

Fuse - Pk/5 - 25mm.(1 inch) Glass Fuse - 15 Amp.- Fits: 1978-84 "Specials".

Fuse - Pk/5 - 25mm.(1 inch) Glass Fuse - 20 Amp.- Fits: 1978-84 "Specials".

Fuse - Pk/5 - 30mm.(1.2 inch) Glass Fuse - 10 Amp.

Fuse - Pk/5 - 30mm.(1.2 inch) Glass Fuse - 15 Amp.

Fuse - Pk/5 - 30mm.(1.2 inch) Glass Fuse - 20 Amp.

100 Amp Battery Cables (8' Long) with alligator clips - For Motorcycle use.

Battery Positive (+) Cable - Fits: XS2 (1972), TX650 (1973).
Approximately 6.5" long.

Cable - Battery relay to starter motor on XS2/TX650 1972-73

Battery Negative (-) Cable to engine block. - Fits: XS2 (1972), TX650 (1973).
Approximately 17" long.

Battery Positive (+) Cable - Fits: 1974-84 650's. Approximately 7" long.

Battery Negative (-) Cable - Frame to negative battery terminal.
Fits:74-84 650's. Approximately 6.5" long.

Cable - Battery relay to starter motor - Fits: 1974-84 650's.
Approximately 21" long.

Replacement Rubber Cap for starter motor power cable terminal.
Fits: All 650's 1972-84.