XS650 Direct

Throttle Cable (Grey) Right side cable for - XS1/XS1B/XS2/TX650 (1970-73)
OEM # 256-26311-01 Made in Japan

Throttle Cable (Grey) Left side for - XS1/XS1B/XS2/TX650 (1970-73)
OEM # 256-26312-00 Made in Japan

Throttle Cable (black) Right side for - TX650A (1974), XS650B (1975)
OEM # 447-26311-00 Made in Japan

Extended Throttle Cable - (Black) Throttle - Same as Throttle cable
#51-3510 (RH throttle cable to fit TX650A/XS650B (1974-75) but + 350mm.
(13.75") in length. Total outer cable casing length including throttle
end adjuster fitting is approx 56.75" (1441mm). Cut the outer cable to
the desired length, crimp on the casing ferule, trim the inner cable
to length and then solder on the carb end cable nipple (ferule and end
nipple included in pack).

Fits: Custom High bar applications (RH side) for TX650A/XS650B (1974-75).

Note: Soldering required and length difference between inner and outer
cables must be kept same as stock cables.

Throttle Cable (Black) Left side for - TX650A (1974), XS650B (1975)
OEM # 447-26312-00 Made in Japan

Extended Throttle Cable - (Black) Throttle - Same as Throttle cable
#51-3510 (LH throttle cable to fit TX650A/XS650B (1974-75) but + 350mm
(13.75") in length). Total outer cable casing length including throttle
end adjuster fitting is approx 56.75" (1441mm). Cut the outer cable to
the desired length, crimp on the casing ferule, trim the inner cable to
length and then solder on the carb end cable nipple (ferule and end nipple
included in pack).

Fits: Custom High bar applications (LH side) for TX650A/XS650B (1974-75)

Note: Soldering required and length difference between inner and outer cables
must be kept same as stock cables.

Retainer Clip - Holds Throttle Cable to throttle housing
Fits: 1970-75 650s with dual throttle cables.

Throttle Cable (Black) Fits: XS650C/D/E/F(1976-79) Standard models and will
also fit 78-84 "Specials" with lower bars. OEM# 584-26311-10 - Made in Japan

Throttle Cable (Black) Fits:XS650 "Specials" (78-84) with Stock pullback bars
and 76-79 Standard models with high bars. OEM# 2M0-26311-01 Made in Japan

Extended Throttle Cable - (Black) Throttle - Same as Throttle Cable
#51-3502 but + 350mm. (13.75") in length. Total outer cable casing
length including throttle end adjuster fitting is approx 58.5" (1485mm).
Cut the outer cable to the desired length, crimp on the casing ferule,
trim the inner cable to length and then solder on the carb end cable
nipple (ferule and end nipple included in pack).

Fits: Custom High bar applications for XS650's (1976-84).

Note: Soldering required and length difference between inner and outer
cables must be kept same as stock cables.

Retainer Clip - Holds Throttle Cable to throttle housing
Fits: 1976-84 650's with single throttle cables.

Throttle Cable (Black) Fits: 1976-84 Stock Throttle to Mikuni VM 34/36/38mm.
Non CV aftermarket carbs. 2-1 type design, machined steel junction box.
- Quality made in Japan.

Also fits XS Performance Keihin PWK 32 Carb Kit (XS Part # 48-9010)

Replacement 2-1 Throttle cable for XS650 PWK 32mm. XS Performance Carb
Set for XS650

Made In Japan

Cable Luber - Yamaha pressure type (Sold each)
Water & dirt are blown down cable by lubricant when pressure spray can nozzle
is applied. Spray lube sold by most bike shops.

Throttle Sleeve - Fits: Stock 1976-84 XS650 OEM Throttle Housing Assembly.

Cable End (for Carb Slide End) 3mm. OD x 3mm Long
x 1.5mm ID (Pk./10) Cable ends for making or repairing
cables.

Cable End (for Carb Slide End) 3mm. OD x 5mm long
x 1.5mm ID. (pk./10) Fits: Lower on VM 2-1 (XS#51-6506).
Cable ends for making or repairing cables.

Throttle Cable End (at Carb) - 6mm. Dia x 7 mm. long - Pk./10
Cable ends for making or repairing cables.

Fits: Cables XS #51-3502/3506/3507/3510/3511 + Upper on XS #51-6506

2 to 1 Cable Junction Box (1 cable in - 2 cables out)
Round Steel Junction with thread on top cap and Nylon
inner slide/Junction.

For Custom Cable Building
Upper Single inlet fits a 6mm. OD outer cable
Lower Dual outlet fits two outer cables of 5mm. OD

Note: Cable Box must be hydraulically crimped to retain
outer cable ends once they are fitted to the junction box.

5mm. ID Cable Ferrule - (Outer cable end cover) - Pk./10
Ferrule Cable ends for making or repairing cables/

Fits: Throttle XS #51-3506/3507 & lower of XS #51-6506

6mm. ID Cable Ferrule - (Outer cable end cover) - Pk./10
Ferrule Cable ends for making or repairing cables.

Fits: Throttle Cables XS #51-3502/3509/3510/3511 +
Decompressor Cable XS #51-6504

Throttle Cable End (at Throttle) for 1.5mm inner cable - Pk./10
Barrel shape - 6mm. Dia x 4.0 mm. long.
Cable ends for making or repairing cables.

Fits: Cables XS #51-3502/3506/3507/3509/3510/3511 + upper on
XS #51-6506.

Black Switch housing Screws (Pk./2)
for Brake (throttle) side handlebar switch.
Holds switch halves together. Fits: 1972-84 650's

NOTE:
These are replacement screws normally
included with switch #24-2059 & #24-2060

Chrome Switch housing Screws (Pk./2)
for Brake (throttle) side handlebar switch.
Holds switch halves together. Fits: 1972-84 650's

NOTE:
These are replacement screws normally
included with switch #24-2062 & #24-2063