XS650 Direct

Early Type Brake caliper - Fits: 1972-76 models - Right or left side and mounting in front or behind the fork leg.

Early Type Master Cylinder Assembly - Fits: 1972-76 650's. Complete with Banjo bolts & washers.

Shims Set(2) to fit early Brake Calipers - Reduces heat transfer to the caliper and in some cases reduces pad rattles & squeeling.

Fits: Early 650's- 1972-76 calipers ( mounts at rear of pad ).

Replacement Bleed screw to fit 1972-76 Round Pad type Brake Calipers

Replacement Hardware to fit 08-6008 caliper and stock original round pad type calipers as used on all 1972-76 650's .

Logo to fit body of early round pad type brake calipers ( 1972-76 650's )

Electronic Speedometer-MPH
With Digital Trip meter-Chrome Cover
matches original gauge. Electronic
pickup. (0-130 MPH)

Fits Yamaha 650's 77-84

Electronic Speedometer-KPH
With Digital Trip meter-Chrome Cover
matches original gauge. Electronic
pickup. (0-220 KPH)


Fits Yamaha 650's 77-84

Electronic Tachometer
Chrome cover matches original tachometer appearance.
(0-10k RPM)

Fits Yamaha 650's 77-84

Polished Valve Cover, 3 Hole Type.

Square Polished Valve Cover, 4 Hole Type.

Commando 2-2 Exhaust System for "Specials" with Upswept Headpipes

XS Performance Keihin Carb Kit for XS650.
32mm Keihin Flatslide PWK Carb Set - Includes: Carbs,
Carb Holder Sets, Gaskets, extra Jets, 2 into 1 Cable,
XS Performance Intake Manifolds and Pod Filters.

These carbs will make your XS start, idle, accelerate
and perform better than any other Japanese carbs.
Our PWK Carbs were Dyno developed by Heiden Tuning and specially
built by Keihin for Mikes XS for use on four strokes.
A superior replacement for the 1980 to 84 stock Mikuni
BS34 Carbs or your worn out BS38's. Kit is designed to be
a drop on installation and jetting should be correct for
most uses (Note: stock air filter box must be removed).
Additional + & - size jets are included with the kit but
probably will not be needed. Cable fits to 1976-84 throttle.

XS Performance Keihin PWK Kit Dyno Chart

OEM Type Rear Master Cylinder Assembly for 1978-80 XS 650 "Specials"
with rear disc brake. Includes plunger rod.

Replacement Rear Master Cylinder Reservoir Assembly
with hose (OEM Type). Direct fit to Master Cylinder
Assembly 08-4008.

Fits: XS650 SE/SF/SG 1978-80

Gas Cap XS1/XS2 with Latch Lever

Ignition Switch with Keys - OEM Ref. # 256-82508-30/31,
366-82508-30

Fits: Yamaha XS1/XS1b/XS2 (1970-72)

2-1 Chrome XS Performance Headpipe Set with collector.
1 1/2" OD Headpipes with Finned Headclamps and a collector pipe
(45.3mm.OD)with a slight kick up.
Note: Muffler NOT Included.

In Dyno Development this system with a free flowing muffler
added and unprecedented 10HP+ rear wheel to a completely stock 1980 XS650.

Designed to work with our taper Tip #07-0041 muffler or our
#07-0114 short megaphone or any free flowing muffler that will fit
onto the 45.3mm (1.783") OD collector. This system produces more
power than any other we have tested or developed.

Dyno Test Sheet