Haynes Service Manual

Product Photo
"Haynes" Service Manual - Covers XS650 1970-83
Part #35-0650
$37.95 CAD Ea
Add to Cart

Carb Cleaning Tool Set

Product Photo
Carburetor Cleaning Tool Set. Includes 12 steel wire ends and a small file designed for cleaning nozzles and the tiny holes found in carburetor passages and jets.
Part #35-9125
$11.95 CAD Ea
Add to Cart

Steering Race Remover 35-55mm

Product Photo
Steering Head Bearing Race Remover, Range 35-55mm ID.

This tool will assist in removing motorcycle steering head bearing races. The size range is from 35mm to 55mm inside diameter. Can be driven with any hammer or mallet. Slips in the headtube solid end first until it snaps in behind the bearing race, then simply drive the race out of the frame.
Part #35-9124
$29.95 CAD Ea
Add to Cart

Bearing Packer

Product Photo
Wheel Bearing Grease Packer. To pack a bearing, place the bearing on the piston, press down on the cap until the old grease is forced out and the new grease shows on top of the bearing. Grease stays in the tool cavity, not on your hands. Transparent, impact resistant cup allows easy grease level checks. Works on bearings up to 3-1/2" OD or 89mm.
Part #35-9122
$33.95 CAD Ea
Add to Cart

Portable Auxiliary Fuel Tank Tool

Product Photo
Portable Auxiliary Fuel Tank, for Non Fuel Injection Systems. Includes 4 Feet of 1/4" fuel line and an inline fuel valve with 1/4" inlet and outlet. Fuel capacity 2 Litres. For use when tuning a motorcycle with the gas tank removed.


Note: This tool is not to be used for long term fuel storage, for safety and to prevent accidental spillage, immediately drain gas back to approved long term storage container after use.
Part #35-9120
$49.95 CAD Ea
Add to Cart

Piston Ring Tool

Product Photo
Piston Ring Tool with plastic storage case. This tool is designed to prevent ring breakage during cylinder installation. This tool can be easily removed after cylinder is in position. Comes with 4 rings to accept the smallest triple to the largest single cylinder engines. Fits 40-85mm sizes.
Part #35-9112
$21.95 CAD Ea
Add to Cart

Carb Cleaning Tool Set

Product Photo
Carburetor Cleaning Tool Set. Includes 20 steel wire ends designed for cleaning the tiny holes found in carburetor jets. Cleaning wire sizes range from 0.45mm to 1.5mm.
Part #35-9110
$13.95 CAD Ea
Add to Cart

Deluxe Shock Preload Adjusting Tool

Product Photo
Deluxe Shock Preload Adjusting Tool. This tool helps to adjust shock preload without damaging the shock spring collars. It fits 35mm to 75mm spring collars.

Fits: Our shock sets and many other aftermarket shocks.
Part #35-9108
$13.95 CAD Ea
Add to Cart

Stud Extractor 6-12mm

Product Photo
Stud Extractor 3/8" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench.

Fits studs from (6-12mm)
Part #35-0103
$24.95 CAD Ea
Add to Cart

Cylinder Stud Installation Tool Set

Product Photo
3 Piece Cylinder Stud Installation Tool Set. Installs studs without damaging the threads. Steel construction with black oxide finish for longer tool life.

Includes M6 x 1.00, M8 x 1.25 and M10 x 1.25 stud installers. Hex head is 19mm.
Part #35-0101
$12.95 CAD Ea
Add to Cart

Extractor & Drill Set

Product Photo
10 Piece Extractor & Drill Set in a Plastic Case. Set contains 5X extractors (#1 through #5) and 5X mechanic's length cobalt drills. Removes bolts and screws up to 5/8".

Cobalt Drill and Screw Extractor Sizes: 5/64", 7/64", 5/32", 1/4", 19/64"
Part #35-0100
$12.95 CAD Ea
Add to Cart

3/8" Drive Click Type Torque Wrench Tool

Product Photo
3/8" Drive Window Click Type Torque Wrench Tool with Black Plastic Storage Case. 10-100Ft. Lbs.

This click-style torque wrench easily tightens various automotive bolts, from lugs and crankshaft bolts to cylinder heads and engine-mountings. Measures from 10 to 100 foot/pounds in .5 increments.
Part #35-0099
$44.95 CAD Ea
Add to Cart

Rectangular Magnetic Parts Dish

Product Photo
Rectangular Stainless Steel Magnetic Parts Dish. Very useful when working with small screws, hardware and parts. 9.5" Length, 5.5" Width, 1.1" Height.
Part #35-0098
$14.95 CAD Ea
Add to Cart

Round Magnetic Parts Dish

Product Photo
Round Stainless Steel Magnetic Parts Dish. Very useful when working with small screws, hardware and parts. 149mm Diameter, 40mm Height.
Part #35-0097
$9.95 CAD Ea
Add to Cart

Wheel Bearing Remover Set

Product Photo
8 Piece Metric Wheel Bearing Remover Set in a Plastic Case. Includes a large and small driver with 10mm, 12mm, 15mm, 17mm, 20mm and 25mm removers. Dependable split collet design.
Part #35-0092
$62.95 CAD Ea
Add to Cart

Carburetor Adjusting Tool

Product Photo
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Part #35-0084
$16.95 CAD Ea
Add to Cart

Steering Bearing Installation Tool

Product Photo
Steering Bearing Installation Tool. Includes one driver and three aluminum adapters. Unique system utilizes specially designed aluminum adaptors to quickly and accurately install nearly any lower bearing. Use with a soft faced hammer.
Part #35-0073
$59.95 CAD Ea
Add to Cart

Brake Bleeder Hose Kit

Product Photo
Brake Bleeder Hose Kit. Kit includes 1-way valve, hose and clamps.

This tool helps bleed motorcycle brakes quickly and easily. The 1-way valve prevents air from flowing back into the brake lines. Easy to use, simply connect and pump.
Part #35-0072
$10.95 CAD Ea
Add to Cart

Chain Alignment Tool

Product Photo
Chain Alignment Tool. This tool provides an easy way to verify your chain is aligned properly to the front and rear sprockets after rear wheel or chain maintenance.

Simply clamp this tool on the rear sprocket with the rod pointing to the front sprocket. With the rod as your guide, make visual alignment then adjust the chain adjusters as needed to correct alignment.
Part #35-0071
$14.95 CAD Ea
Add to Cart

Aluminum Vise Insert

Product Photo
Aluminum Vise Insert. A perfect addition to make your workbench vise more versatile. Three machined semi circles to hold 5/16" to 9/16" size parts you need to grip. The bridge spring keeps the jaws aligned and allows the inset to open precisely with the vise.
Part #35-0068
$21.95 CAD Ea
Add to Cart

419pc O-Rings Kit with Plastic Case

Product Photo
419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes.

QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia.
20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm
23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm
23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm
23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm
20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm
18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm
14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm

13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm
10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm
10X---3.50mm--20.00mm----------10X---3.50mm--34.50mm
10X---3.50mm--22.00mm----------10X---3.50mm--36.00mm
10X---3.50mm--23.50mm----------10X---3.50mm--38.00mm
10X---3.50mm--25.00mm----------10X---3.50mm--41.00mm
10X---3.50mm--26.50mm----------10X---3.50mm--44.00mm
10X---3.50mm--28.00mm----------10X---3.50mm--47.00mm
10X---3.50mm--30.00mm----------10X---3.50mm--50.00mm
Part #35-0067
$27.95 CAD Ea
Add to Cart

382pc O-Rings Kit with Plastic Case

Product Photo
382pc O-Rings Kit with Plastic Case. 30 different sizes included in mm's.

QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia.
20X---1.78mm--2.90mm------------13X---2.62mm--9.19mm
20X---1.78mm--3.69mm------------13X---2.62mm--10.77mm
20X---1.78mm--4.47mm------------13X---2.62mm--12.37mm
20X---1.78mm--5.29mm------------13X---2.62mm--13.95mm
20X---1.78mm--6.07mm------------13X---2.62mm--15.54mm
20X---1.78mm--7.65mm------------13X---2.62mm--17.12mm
20X---1.78mm--9.25mm------------13X---2.62mm--18.72mm

10X---3.53mm--18.64mm----------10X---3.53mm--31.34mm
10X---3.53mm--20.22mm----------10X---3.53mm--32.92mm
10X---3.53mm--21.82mm----------10X---3.53mm--34.52mm
10X---3.53mm--23.39mm----------10X---3.53mm--36.10mm
10X---3.53mm--25.00mm----------10X---3.53mm--37.70mm
10X---3.53mm--26.57mm------------7X---5.34mm--37.47mm
10X---3.53mm--28.17mm------------7X---5.34mm--40.65mm
10X---3.53mm--29.75mm------------7X---5.34mm--43.82mm
Part #35-0066
$24.95 CAD Ea
Add to Cart

Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit

Product Photo
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter.

Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.

Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
Part #35-0065
$54.95 CAD Ea
Add to Cart

Tire Lever - 16.5" Spoon Type w Handle

Product Photo
Tire Lever - 16.5" Spoon Type, Forged Steel with Plastic Handle.
Part #35-0063
$17.95 CAD Ea
Add to Cart

Tire Lever - 11" Spoon Type w Handle

Product Photo
Tire Lever - 11" Spoon Type, Forged Steel with Plastic Handle.
Part #35-0060
$11.95 CAD Ea
Add to Cart

Brush Cleaning Tool

Product Photo
Blue Chain Cleaning Brush/ Gear Cleaner Tool.
Part #35-0055
$12.95 CAD Ea
Add to Cart

T Handle Hex Key Set (Metric Type)

Product Photo
T Handle Hex Key Set (Metric Type), with Metal Holder.

Contains Sizes- 2.0mm, 2.5mm, 3.0mm, 4.0mm, 4.5mm, 5.0mm, 5.5mm, 6.0mm, 8.0mm, 10.0mm
Part #35-0054
$24.95 CAD Ea
Add to Cart

Chain Clip Link Remover Pliers

Product Photo
Chain Clip Link Remover Pliers. Slim jaw design allows for easy install and removal of chain clip links.
Part #35-0050
$22.95 CAD Ea
Add to Cart

Hose Remover Pliers

Product Photo
Hose Remover Pliers. For easy removal of 5/32" to 1/2" hoses. The jaw digs into the tube to grip it, squeeze and the hose is easily pushed off by the jaw.
Part #35-0049
$12.95 CAD Ea
Add to Cart

Mikuni Tuning Manual for Motorcycle Carburetors

Product Photo
Mikuni Carburetor Tuning Manual from Sudco.

92 page manual includes exploded parts views, parts listings and optional parts.
Guides you through tuning and trouble shooting for the popular lines of Mikuni
carburetors. The definite reference for Mikuni carburetors and a must for the
do-it-yourself type.

For Mikuni Pocket Tuner, see XS#48-8106.
Part #35-0665
$18.95 CAD Ea
Add to Cart

Mikuni Pocket Tuner

Product Photo
Mikuni Pocket Tuner. A handy pocket-size calculator which can be used
to determine required jetting changes in Mikuni carburetors due to climate
and temperature changes. The Pocket Tuner is applicable to both single and
multi-carb applications on two-stroke and four-stroke engines. It also has
a guide for determining rich or lean carburetor conditions.

For Mikuni Tuning Manual see XS#35-0665 (Above).
Part #48-8106
$11.95 CAD Ea
Add to Cart

Autosol Metal Polish

Product Photo
3.33 oz. (75 ml) Tube of Autosol Metal Polish.

Cleans, polishes, protects and removes corrosion. For all metal parts-chrome,
brass, copper, nickel, stainless steel & aluminum. Made in Germany since 1929.

"A product that is superior to anything else available"
Part #05-9004
$13.95 CAD Tube
Add to Cart

Seal Puller Tool

Product Photo
Seal Puller Tool
Part #35-8000
$15.95 CAD Set
Add to Cart

Engine Valve Shim Kit Yamaha XS400 XS750 XS850 XS1100

Product Photo
Engine Valve Shim Kit, 29mm Diameter.

Contains 20 pieces: 2 Each 2.3/2.4/2.5/2.55/2.6/2.7/2.8/2.9/3.0/3.1

Note: NOT for the XS650, just for the models below.

Fits: XS750 D/2D/F 1977-79, XS750 SE/SF 1978-79, XS850 G/H 1980-81, XS850 LG/SG/SH 1980-81, XJ900 RK 82, XJ900 83-85, XJ1100 J 82, XS1100 E/F/G/H 1978-81, XS1100 LG/LH 1980-81, XS1100 SF/SG/SH 1979-81, XS400 J/K 1982-83, XS400 RJ/RK 82-83, XJ550 81-83, FJ600 L/N 84-85, FZ600 86-88, XJ600 84, XJ650 G/H/K 80-83, XJ650 LH 81, XJ650 RJ 82, XJ650 83, XJ650 LJ/LK 82-83XJ750 J/K 82-83, XJ750 MK 83, XJ750 RH/RJ/RK 81-83
Part #43-0115
$189.95 CAD Kit
Add to Cart

Metric Go Thru Socket Set

Product Photo
Metric Go Thru Socket Set - Rachet and Extension Hold Socket from the Outside
Eliminating the Need for Deep Sockets. Reaches in Deep.

Set includes Thin Go Thru Rachet and Extension + 6 pint Go thru Sockets sizes
- 19mm., 17mm.,16mm., 15mm., 14mm., 13mm., 12mm., 11mm., 10mm.,+

1/4" Drive adaptor with matching Sockets in Sizes
- 14mm., 13mm.,12mm., 11mm., 10mm., 9mm., 8mm., 7mm., 6mm., 5.5mm., 5mm., 4.5mm., & 4mm.

In plastic latched case.
Part #35-9056
$39.95 CAD Set
Add to Cart

Metric 10pc. T-Handle Nut Driver Set

Product Photo
Metric Nut Driver Set - Quality Forged Chrome 6 point Drivers with T-Handle
Rachet with Quick Release. Set includes 3/8 drive rachet handle and 11 1/2"
inch long drivers in Deep mm sizes - 8,9,10,11,12,13,14,17 & 19mm.
Includes folding case.
Part #35-9054
$59.95 CAD Set
Add to Cart

Graduated Cylinder

Product Photo
1,000cc (1 Liter) Plastic Graduated Cylinder for Accurate Measuring of Fluids.

1 US Quart = 946cc (946ml)
Part #35-2212
$14.95 CAD Ea
Add to Cart

Graduated Cylinder

Product Photo
500cc (1/2 Liter) Plastic Graduated Cylinder for Accurate Measuring of Fluids.
Part #35-2211
$13.95 CAD Ea
Add to Cart

Graduated Cylinder

Product Photo
250cc (1/4 Liter) Plastic Graduated Cylinder for Accurate Measuring of Fluids.
Part #35-2210
$11.95 CAD Ea
Add to Cart

Fork Oil Level Gauge

Product Photo
Fork Oil Level Gauge for Adjusting the Oil Level on all XS650 Forks.
Adjustable ring measures oil levels from 0-300mm in 50mm increments.
60ml capacity syringe adjusts fluid levels.
Part #35-1084
$21.95 CAD Ea
Add to Cart

Graduated Cylinder

Product Photo
1,000cc (1 Liter) Plastic Graduated Cylinder for Accurate Measuring of Fluids.

1 US Quart = 946cc (946ml)
Part #35-2212
$14.95 CAD Ea
Add to Cart

Long 27mm Combination Wrench

Product Photo
27mm Box Wrench to fit XS650 Oil Drain Plugs. Long (15") Type for Leverage to
Loosen Those Tight Oil Plugs.
Part #35-1083
$15.95 CAD Ea
Add to Cart

Fork Cap Box Wrench

Product Photo
32mm 6 Point Box Wrench - Chrome Plated Steel. Also has 39mm Size.
Part #35-1080
$13.95 CAD Ea
Add to Cart

Fork Tube Cap Tool

Product Photo
17mm Hex (Allen) Bit Tool to Remove Fork Tube Top Caps. A perfect fit to
remove those soft alloy fork tube caps without damage.

Fits: Fork caps on TX650A (1974), XS650BC (75-76) and 1977D (version without
preload adjuster).
Part #35-1081
$6.95 CAD Ea
Add to Cart

22mm Fork Cap Wrench

Product Photo
22mm 12 Point Fork Cap Wrench. Removes Alloy Fork Tube Caps.

Fits: TX650 (1973), XS650 (1978-84)
Part #35-1076
$6.95 CAD Ea
Add to Cart

Battery Jumper Cables

Product Photo
100 Amp Battery Cables (8' Long) with Alligator Clips - For Motorcycle Use.
Part #35-9004
$21.95 CAD Set
Add to Cart

AGM Battery Charger

Product Photo
Deluxe 12 Volt Battery Charger for AGM (Absorbed Glass Mat), Maintenance free,
VRLA, Gel and conventional flooded lead acid batteries. UL & CSA Approved.
Output is 1.25 Amps, 12 volt DC (maximum 14.5 Volts). 4 Stage Microprocessor
controlled charging with automatic shutoff at full charge. 120v AC Input.

1. Qualification - Ensures battery is safe to charge, and has minimum 3 Volts.
2. Bulk Charge - Raises battery to 80 percent of full voltage.
3. Absorption - Holds battery voltage at 80 percent and forces current to top battery
4. Float Mode - Maintains the fully charged battery at a proper working voltage.

Charger Features - 6 LED indicators to show charging status, reverse polarity
protection, overheat protection, overcharge protection and spark proofing.
Full instructions, quick disconnect alligator clip leads and fused eye terminal
leads included. (Not for outdoor use).
Part #42-3512
$44.95 CAD Ea
Add to Cart

Continuity Tester

Product Photo
Electrical Continuity Tester (Use with Power Off) - Detects open circuit in fuses,
diodes, switches, sockets and wires (requires one AA battery - Not included).
Long 48" leads.
Part #35-9008
$6.95 CAD Ea
Add to Cart

Circuit Tester

Product Photo
Electric Circuit Tester - Checks all motorcycle primary electrical and computer
circuits for power. Plastic handle lights up if circuit is good. Icepick type
probe and 48" cable with insulated alligator clips.
Part #35-9009
$11.95 CAD Ea
Add to Cart

Terminal Crimper Tool

Product Photo
Metric Terminal Crimper Tool, Fastens Metric Terminals to Wires.
Professionally Crimps Like Factory Originals.
Part #35-0011
$37.95 CAD Pc
Add to Cart

Alternator Rotor Puller

Product Photo
Alternator Rotor Puller - Safely Pulls Rotor Without Damaging it.

Fits: All 650's
Part #35-0040
$16.95 CAD Ea
Add to Cart

Cable Luber - Yamaha Pressure Type

Product Photo
Cable Luber - Yamaha Pressure Type (Sold Each)

Water & dirt are blown down cable by lubricant when pressure spray can nozzle
is applied. Spray lube sold by most bike shops.
Part #35-0108
$8.95 CAD Ea
Add to Cart

Precision Carb Sync Gauges

Product Photo
Dual Carb Sync Gauge Set with Built in Adjustable Pulse Dampers Mounted
on Bracket and with Hoses. Precision Diaphragm type gauge set originally
designed for Professional Motorcycle shop use in Japan.

Note: Sync gauges hoses hook up to carb holder vacuum air barbs
(not included). Your bike must have these air barbs in order to use
this sync tool.
Part #35-1388
$79.95 CAD Set
Add to Cart

Timing Light

Product Photo
Inductive Xenon Timing Light. Operates from 12 Volt Battery Power.
The only accurate way to set your 650's Timing and check advance.
Part #35-9000
$41.95 CAD Ea
Add to Cart

Spark Plug Gap Tool

Product Photo
Circular Spark Plug Gap Tool. Marked in thousandths of an inch and millimeters.
Part #35-0136
$3.50 CAD Ea
Add to Cart

9pc. Feeler Guage Set

Product Photo
Feeler Guage Set - Metric Feeler Guage Set for Setting Valve Clearances.
9pc. Set (Marked in Metric Sizes Only).

0.229mm. - (.009")
0.381mm. - (.015")
0.406mm. - (.016")
0.432mm. - (.017")
0.457mm. - (.018")
0.483mm. - (.019")
0.508mm - (.020")
0.533mm - (.021")
0.660mm. - (.026")
Part #35-1766
$10.95 CAD Set
Add to Cart

12pc. Feeler Gauge Set

Product Photo
Feeler Gauge Set With 45 Degree Ends. Marked in Metric and Inch Sizes.

0.20mm. - (.008")
0.25mm. - (.010")
0.30mm. - (.012")
0.33mm. - (.013")
0.35mm. - (.014")
0.38mm. - (.015")
0.40mm. - (.016")
0.45mm. - (.018")
0.48mm. - (.019")
0.50mm. - (.020")
0.63mm. - (.025")
0.65mm. - (.026")
Part #35-1767
$11.95 CAD Set
Add to Cart

20pc. Feeler Gauge Set

Product Photo
Feeler Gauge Set - Metric Feeler Gauge Set for Setting Valve and Contact
Point Clearances. 20pc. Set (Marked in Metric Sizes Only).

0.05mm. - (.002") 0.55mm. - (0.22")
0.10mm. - (.004") 0.60mm. - (0.24")
0.15mm. - (.006") 0.65mm. - (0.26")
0.20mm. - (.008") 0.70mm. - (0.28")
0.25mm. - (.010") 0.75mm. - (0.30")
0.30mm. - (.012") 0.80mm. - (0.32")
0.35mm. - (.014") 0.85mm. - (0.34")
0.40mm. - (.016") 0.90mm. - (0.36")
0.45mm. - (.018") 0.95mm. - (0.38")
0.50mm. - (0.20") 1.00mm. - (0.40")
Part #35-1768
$12.95 CAD Set
Add to Cart

32pc. Feeler Gauge Set

Product Photo
Feeler Guage Set - Metric/Inch Feeler Gauge Set for Setting Valve and Contact Point
Clearances. 32pc. Set (Marked in Metric and Inch Sizes).

0.03mm. - (.001") 0.04mm. - (.0015") 0.05mm. - (.002") 0.06mm. - (.0025")
0.07mm. - (.0028") 0.08mm. - (.003") 0.09mm. - (.0035") 0.10mm. - (.004")
0.13mm. - (.005") 0.15mm. - (.006") 0.18mm. - (.007") 0.20mm. - (.008")
0.23mm. - (.009") 0.25mm. - (.010") 0.28mm. - (.011") 0.30mm. - (.012")
0.33mm. - (.013") 0.35mm. - (.014") 0.38mm. - (.015") 0.40mm. - (.016")
0.45mm. - (.018") 0.50mm. - (0.20") 0.55mm. - (.022") 0.60mm. - (0.24")
0.63mm. - (.025") 0.65mm. - (0.26") 0.70mm. - (0.28") 0.75mm. - (0.30")
0.80mm. - (0.32") 0.85mm. - (0.34") 0.90mm. - (0.36") 1.00mm. - (0.40")
Part #35-1769
$21.95 CAD Set
Add to Cart

Compression Tester

Product Photo
Cylinder Compression Tester Set with Quick Coupling & Release Valve.
Includes Adapters to Fit 10, 12, 14, & 18mm Spark Plug Holes.
Part #35-9030
$74.95 CAD Set
Add to Cart

Compression Test Gauge

Product Photo
Cylinder Compression Tester with Quick Coupling, Universal Adapter and
Flex Hose with 14mm Threaded End.
Part #35-9031
$57.95 CAD Kit
Add to Cart

Piston Pin Puller

Product Photo
Piston Pin Puller with Adaptors (12.5, 15.75, 19, 22mm OD).
Easily Removes XS650 Piston Pins (20 & 22mm OD) Without Damage.
Part #35-9070
$39.95 CAD Ea
Add to Cart

Inspection Mirror

Product Photo
30mm Diameter Inspection Mirror on Telescoping Wand 7-20" Range.
Part #35-9035
$8.95 CAD Ea
Add to Cart

Image Scope

Product Photo
Professional Flexible Fibber Optic Image Scope for Inspecting
Engine Internal Parts.

18" long wand with a 6mm (1/4") OD tip. Image resolution is 7,400 pixels.
Packed in a blow mold case with handle jacket and extra Xenon Bulbs and
2 AA batteries.
Part #35-9096
$159.95 CAD Ea
Add to Cart

45 Degree Adaptor for Image Guide Scope

Product Photo
45 Degree Adaptor for Image Guide Scope
Part #35-9098
$47.95 CAD Ea
Add to Cart

Magnet with Light

Product Photo
29" Long Flex Rod with Lighted Magnetic Tip.
Part #35-9034
$14.95 CAD Ea
Add to Cart

Flexible Magnet Tool

Product Photo
Flexible Rod with Magnetic Tip. 23" Long, Picks up to 3.5 Lbs.
Part #35-9036
$12.95 CAD Ea
Add to Cart

Hook and Pick Set

Product Photo
5pc. Hook and Pick Set with Magnet in Handle End.
Part #35-9038
$9.95 CAD Set
Add to Cart

Metric Thread Pitch Gauge

Product Photo
Thread Pitch Gauge for Measuring Metric Thread Pitch (Threads Per Millimeter).

A very useful tool to identify the many various fastener threads used on
Japanese bikes. Gauge has the following sizes - 0.5, 0.6, 0.7, 0.8, 0.9, 1.0,
1.25, 1.75, 2.7, 2.8.
Part #35-8031
$8.95 CAD Ea
Add to Cart

Metric Tap & Die Set

Product Photo
Metric Tap & Die Set in Storage Case.
Set includes Pitch Gauge, Die Holder, 2 Tap Wrenches & Screw Driver +

Metric Taps - M3 x 0.5, M3 x 0.6, M4 x 0.75, M4 x 0.7, M5 x 0.8, M5 x 0.9,
M6 x 1.0, M6 x 0.75, M7 x 0.75, M7 x 1.0, M8 x 1.0, M8x 1.25, M10 x 1.25,
M10 x1.5, M12x 1.25, M12 x 1.5, 1/8NPT x 27

Metric Dies - 17 Dies to Match Taps Listed Above.
Part #35-8030
$89.95 CAD Set
Add to Cart

Cam Chain Tool Kit

Product Photo
Cam Chain Tool Kit in Case - A "Must Have" Tool to Break and Rivet Cam Chains.

Note: Do Not Use for Rear Drive Chains.
Part #35-0112
$67.95 CAD Kit
Add to Cart

Replacement Breaker Pin

Product Photo
Replacement Breaker Pin for Cam Chain Breaker Tool.
Part #35-0117
$8.50 CAD Ea
Add to Cart

Rocker Shaft Slide Hammer

Product Photo
Slide Hammer with Correct Bolt Thread to Remove Engine Rocker Arm
Shafts from Head Cove.

Works on All 1970-84 650's
Part #35-0121
$19.95 CAD Ea.
Add to Cart

Valve Spring Compressor

Product Photo
Valve Spring Compressor - Large Honda Heavy Duty Type.

This style valve spring Compressor works best on the XS650.
Part #35-0122
$99.95 CAD Ea.
Add to Cart

Valve Spring Compressor Tool

Product Photo
Valve Spring Compressor Tool in Case. High Quality Professional Tool
to Remove Valve Springs.

Now with 5 Tips! - 16, 19, 23, 25 & 30mm. Dia.
Part #35-0115
$64.95 CAD Set
Add to Cart

Valve Guide Install / Remove Driver Tool

Product Photo
Valve Guide Install / Remove Driver Tool for 1970-84 650's
Part #35-0077
$9.95 CAD Ea
Add to Cart

Valve Lapping Sticks

Product Photo
Valve Lapping Sticks - Set/2
Part #35-0059
$9.95 CAD Set/2
Add to Cart

Valve Seat Cutting/Finishing Tool Kit

Product Photo
Tool Kit for Doing 3 Angle Valve Seat Cutting & Finishing.
Kit was Created Specifically for Overhauling the XS650 Cylinder Head.

Works on All 1970-84 650 engines.

Kit Contains:
1 - Precision ground T-Handle Valve guide Pilot
1- 36 x 45 degree Carbide Cutter
1- 43 x 30 degree Carbide Cutter
1- 43 x 45 degree Carbide Cutter
1- 43 x 60 degree Carbide Cutter
1- 36 x 45 degree Finishing Stone
1- 42 x 45 degree Finishing Stone
1- Set/2 Valve Lapping Sticks
1- Tube Valve Lapping Paste
Part #35-0116
$169.95 CAD Kit
Add to Cart

Permatex Valve Lapping Paste

Product Photo
Permatex Valve Lapping Paste
Part #35-0120
$8.95 CAD Tube
Add to Cart

Replacement Valve Seat Grinding Stone

Product Photo
1- 36mm. Dia. x 45 Degree Replacement Valve Seat Grinding Stone for Kit #36-0116
Part #35-0118
$17.95 CAD Ea.
Add to Cart

Replacement Valve Seat Grinding Stone

Product Photo
1- 42mm. Dia. x 45 Degree Replacement Valve Seat Grinding Stone for Kit #36-0116
Part #35-0119
$17.95 CAD Ea.
Add to Cart

JIS Screwdriver Set

Product Photo
JIS Screwdriver Set/3.

Every screw on every Japanese designed motorcycle from the 1950s right up to the
newest bikes in the showroom today were manufactured with a unique JIS screw head
design we don't see on products made here in North America.

JIS screwdrivers grip the screw and fit snugly rather than just sitting inside ensuring
a perfect fit every time which greatly increases the probability of removing that screw
with no damage.

This set of three screwdrivers covers the majority of sizes needed on Japanese motorcycles

1-JIS style screwdriver-size #1 - perfect for those little screws on handlebar switches- electrics- etc
1-JIS style screwdriver-size #2 - our most versatile- great for all carb screws- etc
1-JIS style screwdriver-size #3 - fits all those larger screws found on the engine cases and bodywork.
Part #200-1713
$31.95 CAD Set
Add to Cart

Impact Screwdriver with Bit Set

Product Photo
Impact Screwdriver with Bit Set in Case. A must have tool used to break loose
engine screws with slot or phillips heads.
Part #35-0095
$19.95 CAD Kit
Add to Cart

Replacement Driver Bit Set (1.5" Long)

Product Photo
Replacement Driver Bit Set (1.5" Long) - Set Contains 2 Phillips & 2 Slotted
Impact Driver Bits.
Part #35-0107
$5.95 CAD Set
Add to Cart

Replacement Driver Bit Set (3" Long)

Product Photo
Replacement Driver Bit Set (3" Long) - Set Contains 2 Phillips & 2 Slotted
Impact Driver Bits.
Part #35-0110
$6.95 CAD Set
Add to Cart

Screw Extractor Set

Product Photo
5pc Screw Extractor Set - Used to Remove Broken Off Studs, Bolts, &
Screws. Set Includes Sizes - 1/8", 3/16", 15/64", 5/16", & 3/8"
Part #35-9048
$18.95 CAD Set
Add to Cart

Pin Punch Set

Product Photo
Metric Pin Punch Set.

Set Includes Small Sizes Usually Not Available:
1.5 mm, 2.0 mm, 3.0 mm, 4.0 mm, 5.0 mm, 5.5 mm, 6.0 mm, & 8.0 mm.
Part #35-9050
$20.95 CAD Set
Add to Cart

Gasket Scraper

Product Photo
15mm wide (9/16") Stainless Steel Gasket Scraper Knife.
Part #35-8002
$10.95 CAD Ea
Add to Cart

Gasket Scraper

Product Photo
20mm wide (.79") Stainless Steel Gasket Scraper Knife.
Part #35-8003
$10.95 CAD Ea
Add to Cart

Deep Allen Socket Screw Driver Set

Product Photo
8 pc Driver Set for Allen Socket Screw.

Hard to find deep 140mm Long bits ideal for reaching up inside lower fork
legs and other recessed spots. Kit includes 1/2" drive socket sizes
5, 6, 7, 8, 10, 12, 14 & 17mm.
Part #35-9049
$42.95 CAD Set
Add to Cart

27mm Deep Socket

Product Photo
1/2" Drive 27mm 6 Point Deep Socket.

Fits: Clutch Hub Nut on All 650's 1970-84
Part #35-1078
$11.95 CAD Ea
Add to Cart

Clutch Holder Tool

Product Photo
Clutch Holder Tool - Holds Inner and Outer Clutch Hubs So That the Center Nut
May be Removed Without Damaging Hubs.

Fits: All 650 clutches (1970-84)
Part #35-5021
$14.95 CAD Ea
Add to Cart

Clutch & Sprocket Holder Tool

Product Photo
Professional Adjustable Vise Grip Style Clutch Basket and Sprocket Holder Tool.
Part #35-9052
$27.95 CAD Ea
Add to Cart

36mm Socket

Product Photo
36mm 1/2" Drive, 6 Point, Impact Socket.

Fits: Front Sprocket on all 650's 1970-84
Part #35-1079
$14.95 CAD Ea
Add to Cart

Drive Chain Riveter Tool

Product Photo
Drive Chain Riveter Tool - Rivets high strength rear drive chain Rivet links with
hollow pin ends as on our IZUMI 530HT Chain (Rivet link #56-0235) and many DID
brand chains.

Extra Rivet Pins Available Below
Part #35-0006
$49.95 CAD Ea
Add to Cart

Replacement Rivet Pin

Product Photo
Drive Chain Rivet Tool Replacement Rivet Pin.

Fits: Drive Chain Riveter Tool #35-0006
Part #35-0007
$8.50 CAD Ea
Add to Cart

Chain Puller Tool

Product Photo
Chain Puller Tool, Pulls new rear drive chain ends together so that
the joiner link can be slipped in place. Ideal for new chains that
are difficult to get together for the first time.
Part #35-0130
$18.95 CAD Ea
Add to Cart

Chain Press Tool

Product Photo
Chain Press Tool. Used to press on sideplates (rivet or clip type) onto rear
drive chains. Most late type High strength drive chains now use a press on
sideplate on the connecting link (including IZUMI 530 HT).
Part #35-0081
$7.50 CAD Ea
Add to Cart

Drive Chain Breaker Tool

Product Photo
Drive Chain Breaker Tool, Breaks 520/530 and 630 Pitch Chain.
Part #35-0083
$29.95 CAD Ea
Add to Cart

Brake Caliper Piston Tool

Product Photo
Brake Caliper Piston Holding/Detaching Tool for 1977-84 Brake Calipers.

Grabs brake caliper pistons internally so seized pistons can be worked
loose from the caliper.
Part #35-1086
$24.95 CAD Ea.
Add to Cart

Vacuum Brake Bleeder Kit

Product Photo
High Quality Vacuum Brake Bleeder Tool Suitable for Motorcycle Use.
All metal construction. This is the best way to get the job done quickly.

Note: Do not use this tool with Speed bleeders.
Part #35-3050
$84.95 CAD Kit
Add to Cart

External Long Arm Snap Ring Pliers

Product Photo
External Long Arm Snap Ring Pliers. Tool spreads the snap ring from
external groove.
Part #35-0009
$15.95 CAD Set
Add to Cart

Spoke Wrench Set

Product Photo
Spoke Wrench Set - A Must Have for Lacing, Truing & Tightening Spokes.
2 Pc. Set.

Fits: #8, 9, 10 & 11 Nipple Sizes.
Part #35-0109
$7.95 CAD Set
Add to Cart

Wheel Weight Tool

Product Photo
Tool for Installing and Removing Spoke or Mag Type Wheel Weights.
Part #35-9059
$14.95 CAD Ea
Add to Cart

Digital Tire Pressure Guage

Product Photo
Digital Tire Pressure Guage, LCD Display, 1-100 PSI.
Part #35-0089
$14.95 CAD Ea
Add to Cart

Tire Lever - 16" Long Dunlop type

Product Photo
Tire Lever - 16" Long Dunlop Type - For those tough tires needing lots of leverage
to remove. You need 2-3 of these to do the job!
Part #35-0080
$12.95 CAD Ea
Add to Cart

Rim Savers (Set)

Product Photo
Rim Savers Set

Designed to protect rims from damage caused by tire Irons when
installing tires on rims.
Part #35-5101
$8.50 CAD Set
Add to Cart

Damper Bolt Driver

Product Photo
Damper Bolt Driver - Deep type damper bolt driver used to air
impact recessed damper bolts from lower fork legs.
Part #35-5022
$9.95 CAD Ea
Add to Cart

Strap Wrench

Product Photo
Strap Wrench with Rubberized Strap for Good Grip. Ideal for holding fork tubes
and other round smooth shapes.

Fits: 29-160mm (1 1/8" - 6 1/4" Diameters)
Part #35-9024
$14.95 CAD Ea
Add to Cart

Shock Ring Wrench

Product Photo
Ring Wrench to Adjust Shock Preload.

Fits: Our 06-3601/06-3607/06-3608/06-3621/06-3627/06-3641 & 06-3647 shock
sets and many other aftermarket shocks.
Part #35-5033
$4.95 CAD Ea
Add to Cart

Ring Wrench

Product Photo
Ring Wrench to Tighten Muffler Joint Nut on Early XS1 Type Muffler
Part #35-5029
$4.95 CAD Ea
Add to Cart

Ring Wrench

Product Photo
Ring Wrench to Tighten Steering Head Cogged Nuts. Also fits preload adjuster
on some stock Yamaha Shocks.
Part #35-3005
$19.95 CAD Ea
Add to Cart

Snap ring Plier Set

Product Photo
Snap ring Plier Set - Removes internal or external snap rings. Set includes 2
straight and 2 angled tips.
Part #35-0114
$15.95 CAD Set
Add to Cart

Spring Puller Tool

Product Photo
Spring Puller Tool - Used to Pull Springs and Hook Them into Place
Part #35-0113
$6.95 CAD Ea
Add to Cart

Heavy Duty Tiedown Set

Product Photo
Heavy Duty Tiedown set - 1 Inch Wide, 5 1/2FT Long, 4000 LB Strength with
Quick Release. Set of 2 (Black Color).
Part #27-5503
$16.95 CAD Set
Add to Cart

Heavy Duty Tie Down Set

Product Photo
Long Heavy Duty Tiedown Set - 1 Inch Wide, 10FT. Long, 4000 Lb. Strength with
Quick Release. Set of 2 (Black Color).
Part #27-5580
$16.95 CAD Set
Add to Cart